WaterBoss 900IF Specifications download pdf

Installation Steps

P repare th e P lac em ent A rea

A. Clean the placement area.

B . Ex amine the inlet plumbing to ensure that the pipe is not plug g ed with lime, iron, or any other sub-

stance. Clean or replace plug g ed plumbing .

Note

: A minimum three-quarter-inch plumbing is required between the pressure tank and the filter for

the filter to function properly.

C. Place your appliance in the desired location using the following diag ram as a g uide. The diag ram

applies to basement, slab, crawl space, and outside installations.

D . F or most installations, install the filter after the pressure tank or water meter and before the water

heater and any water softener appliance unless otherwise recommended. W hen installing the 9 00CF

Carbon F ilter for

ell water

, place the filter after any water softener appliance unless otherwise recom-

mended. Contact the H elpL ine for further assistance in determining the proper installation sequence.

Caution: If less than 10 feet of pipe connects the water treatment appliance(s) to the water heater,

then a check valve must be installed between the water treatment appliance and the water heater.

Install the check valve as close to the water heater as possible. Ensure that the water heater has an

adequately rated temperature and pressure safety relief valve.

T u rn O ff W ater Su pply

A. Turn off the water supply.

B . O pen the hot and cold water to depressuriz e the lines.

STEP 1

STEP 2

1 2 3 4 5 6 ... 12 13

Summary of Contents

Page 1 - Installation Steps

Installation StepsP repare th e P lac em ent A reaA. Clean the placement area.B . Ex amine the inlet plumbing to ensure that the pipe is not plug g e

Page 2

Total Iron_____ ppm 1 =×____ ppm_2.4_ ppm 1 =× 2.4 ppm+ Manganese*_____ ppm 3 =×____ ppm_0.2_ ppm 3 =× 0.6 ppm+ Sulfur_____ ppm 5 =×____ ppm_

Page 3

Setting the ControllerSet the Freq uency of Regeneration or BackwashA. Press and hold the SET button for three seconds. When “01” displays, release th

Page 4 - Helpful Installation Tips

Replenishment Procedure—900NF AcidNeutralizing FilterThe 900NF appliance requires periodic (annual) replenishment of the neutralizing media that adjus

Page 5

Replenishment Procedure—900NF AcidNeutralizing FilterAdd Replenishment MediaA. Measure the required amount of media (P/N M050) by weight on an analog

Page 6 - Plug in the Transformer

Connect Water LinesA. Lift and remove the valve cover. (Lift back first.)B. Attach the water lines to the appliance. Do NOT over– tighten the connecti

Page 7 - 900NF Acid Neutralizing

Installation StepsF lush LinesA. Ensure that the appliance is in bypass mode. See diagram. The bypass valve can isolate the appliance shouldthe system

Page 8 - Add Potassium Permanganate

Helpful Installation TipsQ est Fitting sQest connection fittings are provided with your appliance. Qest fittings provide a convenient easy-to-use thre

Page 9 - Start the Regeneration Cycle

Helpful Installation TipsPlastic (PVC/CPVC) Pipe Joining Procedures (cont.)D.Inspection, Cleaning, and Priming—Inspect the inside of the pipe and fitt

Page 10 - Setting the Controller

ImportantTheWaterBoss®900CF Carbon Filter is capable of treating a combination of undesirable constituents (chlorine,taste, and odor) in water. Instal

Page 11

Plug in the TransformerA. Plug the transformer into an appropriate outlet. The transformer is 120 volt, 60 cycle ac for locations in the USA or 220 vo

Page 12 - Neutralizing Filter

Start-Up Procedures—900IF Iron FilterImportantTheWaterBoss®900IF Iron Filter is capable of treating a combination of undesirable constituents (iron an

Page 13

Plug in the TransformerA. Wait 15 minutes after adding potassium permanganate.B. Plug the transformer into an appropriate outlet. The transformer is 1